How to Adjust Old cabinet Door Hinges
It is pretty normal to encounter door hinges that are pretty loose especially when these things are a bit older than what they look. As a result, better do something about it right away so that would be one less problem to worry about. Believe it or not, it won’t really take too long to know how to adjust old cabinet door hinges. You will even add something to your repertoire because you will encounter this one way or the other. The only thing you will need is a Philips screwdriver as this tool has proven to be pretty much useful when you come to think of it. Of course, you will need to be a bit patient when you finally start the process. It is common to think that you would actually need drills for this but that is out of the way. Here are the right steps to undertake when fixing door hinges:
The cause of your problem can either be sagging or uneven screws. When it is uneven then you would not have much to worry about since you would just need to tighten one of the screws until it is tight enough to perfection. If it is sagging then you are very well familiar with the fact that it is a bit too heavy. If that is the case then you should buy a completely new one. DOn’t worry though because it would be for the benefit of the overall look of your home. Besides, you can’t let this problem last a bit longer without actually doing something about it. Another solution to that would be adding the hinges which are just adding the support to it. Once the problem is identified, the solution for it would be the one you should really be focused on.
Tighten and Adjust
Use the Philips screwdriver and move it clockwise. If you need to loosen it up a bit then do it the other way around. It won’t be long before it would be pretty tight. There will come a time when you would need to find a new hinge altogether. When that happens, keep in mind the most common type of hinge is the fully adjustable hinge. Be sure to buy from a reputable brand so that you will get outstanding service. Luckily, we have a lot of that and we know sharing is caring. It is possible that the hole is a bit stripped so you would need a bunch of large screws in order to remedy the problem. It is amazing how you would just need to replace a few items and it can already be done the way you wanted it to.
Check the Alignment
When you close the cabinet doors, make sure that they are up to par with the rest of them. After all, this is not really the time when you can afford to make a mistake. One small miscue and you could be doing it all over again. It is quite possible one problem you are experiencing right now is that the cabinet doors are just too loud when you close them. Believe it or not, you would need a lubricant for this so go to the nearest hardware store and buy it. Besides, that is where you would need to get on with it in order to get rid of that noise once and for all. You may even decide to get a magnet pull as a temporary solution for cabinets that won’t close. Of course, remember that this is only temporary until you find the right people to do something about it. You can’t really be satisfied with something that is only half done. It would be better if it is all the way so that you can see for yourself that it is something you’ve been meaning to do for quite a while.
Continue Adjusting the Screws
Believe it or not, you may have to do this several times until you are pretty confident that you get the perfect fit that you finally need. This is the reason why you need the right amount of patience for this process. The good news is that it will be all worth it in the end when you finally get on with what you saw and move on from there. You can also get the opinion of other people there with you if it is finally up to par with their tastes. When some of your materials there are not working as well they used to, it would be time to finally call for a replacement. No matter how much you would hate to admit it, it is inevitable. After all, this would be for the benefit of the overall product when you look forward to nice things in the future. There will be times when you would just need to adjust it a bit until you are truly satisfied with the final outcome. Of course, that is a lot easier said than done.
When you need any tips or advice regarding how to adjust old cabinet door hinges then have no fear because we are here for you. Venace is a company that is pretty good at this and we let our actions do the talking. After all, we’ve been in the industry for plenty of years and we’ve learned a lot of things that only experience can teach. This is why we are right up there with the best of them. We are always head and shoulders above the rest of the competition. We are proud of what we have to offer and we will gladly answer any questions about our huge range of products. It is even easy to reach us online as you can be sure a member of our highly skilled customer service team would be available right away. That is actually not a coincidence as we meant for it to be that way so that nobody would be kept waiting at any time during the day.